Security Clearances - United States Department of State
For assistance with completing your security clearance package for a Department of State investigation or to inquire about the status of your security clearance with the Department of State, you may email the DSS Office of Personnel Security and Suitability Customer Service Center at [email protected] or call between 8 A.M – 5 P.M
Get a quote
SOP for Line Clearance (LC) of Area and Equipments
Mar 28, 2020 · Equipment Clearance: It is defined as the clearance certification for the equipment, documents & the required cleanliness as per the type of cleaning are satisfactory then fill the 'Line clearance checklist' as per the relevant Annexure-2/3/4 or respective BMR/BPR and sign along with the date in the required column(s).
Get a quote
Construction Services - aps
Construction Services. Before you get started with construction, we'll get you started with what you need to know about energy for your project. From helpful resources and self-help to requirements, safety guidelines, energy efficiency, contacts and more, we'll help you with what you need to be successful.
Get a quote
How much access is required to build a swimming pool
Minimum access requirements are a working width or opening the size of a standard doorway. A standard pool excavation with good access requires a 3 tonne bobcat, 4.0 tonne excavator and tandem truck. The average pool builder would allow $5,000 for excavating an 8.0 x …
Get a quote
1926.1411 - Power line safety-while traveling under or
NEC + OSHA Electrical Panel Clearance Requirements
Get a quote
ELECTRIC EQUIPMENT OWNERSHIP & REQUIRED METER …
ELECTRIC EQUIPMENT OWNERSHIP & REQUIRED METER CLEARANCES 2' 2' 3' 6' Required Meter Clearances For safe meter access, a clearance I of four feet wide by three feet deep by six feet high is required (see diagram, left). Please keep shrubs, debris, fences and other structures clear of this area. For your safety and ours, do not tamper with
Get a quote
1926.1410 - Power line safety (all voltages)--equipment
In transit with no load and boom lowered, the equipment clearance shall be a minimum of 4 feet for voltages less than 50 kV, and 10 feet for voltages over 50 kV, up to and including 345 kV, and 16 feet for voltages up to and including 750 kV;
Get a quote
CONSTRUCTION SAFETY AND HEALTH STANDARD PART 15
Mar 15, 2016 · excavators, personnel hoists, material hoists, elevators, helicopters, conveyors, and variations of such equipment when used during construction operations. (2) This part applies to equipment included in subrule (1) of this rule when used with any attachment, whether mechanically attached or suspended.
Get a quote
Do you need clearance for a disconnect switch? | Mike Holt
Aug 28, 2019 · Working space for equipment operating at 600 volts, nominal, or less to ground and likely to require examination, adjustment, servicing, or maintenance while energized shall comply with the dimensions of 110.26(A)(1), (A)(2), and (A)(3) or as required or permitted elsewhere in this Code." Note the word equipment above and devices below Equipment.
Get a quote
What is clearance and creepage distance of insulation
Sep 15, 2020 · The clearance of equipment set in the IEC 62368-1 is all used under 2000 meters above sea level. If there is a high altitude requirement, you need to multiply the obtained clearance by the factor required for different altitudes, according to Table 1.
Get a quote
CHAPTER 13 GENERAL MECHANICAL SYSTEM REQUIREMENTS
REQUIRED CLEARANCE WITH NO PROTECTION (See Figures M1306.1 and M1306.2) WHERE THE REQUIRED CLEARANCE WITH NO PROTECTION FROMAPPLIANCE, VENT CONNECTOR, OR SINGLE WALL METAL PIPE IS: 36 inches 18 inches 12 inches 9 inches 6 inches Allowable clearances with specified protection (Inches)b Use column 1 for clearances above an appliance or horizontal
Get a quoteBLOCKS FILE trans clear (1)
a. all dimensions are measured from the equipment pad edge. b. a minimum 30-foot vertical clearance is required from finished grade in aps equipment areas to above surrounding unobstructed staging areas. the 30-foot vertical clearance shall also apply to customer's overhead structures above buried aps electrical facilities / right-of-way.
Get a quote
2015 IMC Sections 304.6 through 312
† If equipment or appliances are suspended above grade, what is the minimum required clearance? † What loads are taken into account when determining the strength of pipe hangers and supports? † Pipe hangers and supports are required to be of compatible material to prevent what from occurring?
Get a quoteConstruction Services - aps
Construction Services. Before you get started with construction, we'll get you started with what you need to know about energy for your project. From helpful resources and self-help to requirements, safety guidelines, energy efficiency, contacts and more, we'll help you with what you need to be successful.
Get a quote
CHAPTER 14-57 RAILROAD SAFETY AND CLEARANCE …
The clearance requirements of this rule do not apply to repair or servicing platforms and structures inside engine houses and repair shops. 4. The minimum side clearance for platforms, eight inches or less above the top of the rail, shall be four feet eight inches. 5.
Get a quote
A Guide to Plant Clearances and Access requirements (with
Equipment Clearance and Access Guidelines Layout and Safety Design Rules for Furnaces and Fired Heaters. Several furnaces in the same or different services and part of the same process unit or facility, together with associated close-coupled equipment, …
Get a quote
Clearance Requirements In EHV AIS Substation You MUST Respect
May 25, 2016 · Clearance requirements you MUST take into account when planning EHV AIS substation (on photo: High voltage transformation substation of the Kimanis Power, in Malaysia; credit: Wikipedia) Substation layout consists essentially in arranging a number of switchgear components in an ordered pattern governed by their function and rules of spatial
Get a quoteNEC + OSHA Electrical Panel Clearance Requirements
1926.1410 (c) (1) The power line owner/operator or registered professional engineer who is a qualified person with respect to electrical power transmission and distribution determines the minimum clearance distance that must be maintained to prevent electrical contact in light of the on-site conditions. The factors that must be considered in making this determination include, but are not limited to: Conditions …
Get a quote
business nbn™ Equipment Location Requirements Guide
nbn-Confidential: Commercial 222 business nbn™ Equipment Location Requirements Guide FTTx Engineering Document number NBN-DES-GDE-3800 Document category Guide Author Network Engineering Solutions & Standards Approver (owner) National Engineering Manager, Network Engineering Solutions & Standards
Get a quote
2015 IMC Sections 304.6 through 312
† If equipment or appliances are suspended above grade, what is the minimum required clearance? † What loads are taken into account when determining the strength of pipe hangers and supports? † Pipe hangers and supports are required to be of compatible material to prevent what from occurring?
Get a quote